Where are you now：
Homepage
>
Industry News
>
What are the reasons for the loud noise in the work of plastic sheet machine?

What are the reasons for the loud noise in the work of plastic sheet machine?

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2021-01-05
  • Views:0

(Summary description)Motor position
① The rolling bearing for rotor shaft is seriously worn or the bearing accuracy is low.
② The rotor shaft is bent and deformed.
③ The installation position of carbon brush is incorrect.
④ Safety cover of rotor shaft end blade wiper motor.
(2) V-belt drive part
① The V-belt pulley of plastic sheet machine is not fixed firmly on the transmission shaft or the fit clearance between the two parts is too large.
② The manufacturing accuracy of pulley is low, and the end face or outer circle swing is large.
③ The poor installation quality of the active and passive pulleys makes the high-speed motion track of V-belt not on the same plane, resulting in working noise.
(3) Working parts of gear transmission
① The gear manufacturing accuracy is low and the pitch error is large.
② The center distance error of the transmission shaft of a pair of meshing gears is large. When the center distance is smaller than the standard, the interference sound between the teeth of the meshing transmission is generated; When the center distance is greater than the standard value, the impact sound will be produced.
③ The rolling bearing on the transmission shaft is worn seriously or the precision is low.
④ The center lines of the two transmission shafts on the gears are not parallel, so that the two gears can not mesh correctly.
⑤ The lubrication condition of a pair of meshing gears is poor. There is not enough lubricating oil
(4) Screw part of plastic sheet machine barrel
① The screw is assembled in the barrel, and the concentricity accuracy of the two parts is low.
② The perpendicularity error between the end face of the barrel and the flange end face of the barrel base and the center line of the barrel is large.
③ The screw is bent and deformed. The straightness error of the axis center line is too large.
④ The assembly clearance between the screw and its transmission shaft is too large. The center line of the two shafts is different from each other during the working rotation, so the error is large.

What are the reasons for the loud noise in the work of plastic sheet machine?

(Summary description)Motor position
① The rolling bearing for rotor shaft is seriously worn or the bearing accuracy is low.
② The rotor shaft is bent and deformed.
③ The installation position of carbon brush is incorrect.
④ Safety cover of rotor shaft end blade wiper motor.
(2) V-belt drive part
① The V-belt pulley of plastic sheet machine is not fixed firmly on the transmission shaft or the fit clearance between the two parts is too large.
② The manufacturing accuracy of pulley is low, and the end face or outer circle swing is large.
③ The poor installation quality of the active and passive pulleys makes the high-speed motion track of V-belt not on the same plane, resulting in working noise.
(3) Working parts of gear transmission
① The gear manufacturing accuracy is low and the pitch error is large.
② The center distance error of the transmission shaft of a pair of meshing gears is large. When the center distance is smaller than the standard, the interference sound between the teeth of the meshing transmission is generated; When the center distance is greater than the standard value, the impact sound will be produced.
③ The rolling bearing on the transmission shaft is worn seriously or the precision is low.
④ The center lines of the two transmission shafts on the gears are not parallel, so that the two gears can not mesh correctly.
⑤ The lubrication condition of a pair of meshing gears is poor. There is not enough lubricating oil
(4) Screw part of plastic sheet machine barrel
① The screw is assembled in the barrel, and the concentricity accuracy of the two parts is low.
② The perpendicularity error between the end face of the barrel and the flange end face of the barrel base and the center line of the barrel is large.
③ The screw is bent and deformed. The straightness error of the axis center line is too large.
④ The assembly clearance between the screw and its transmission shaft is too large. The center line of the two shafts is different from each other during the working rotation, so the error is large.

  • Categories:Industry News
  • Author:
  • Origin:
  • Time of issue:2021-01-05
  • Views:0
Information
Motor position
① The rolling bearing for rotor shaft is seriously worn or the bearing accuracy is low.
② The rotor shaft is bent and deformed.
③ The installation position of carbon brush is incorrect.
④ Safety cover of rotor shaft end blade wiper motor.
(2) V-belt drive part
① The V-belt pulley of plastic sheet machine is not fixed firmly on the transmission shaft or the fit clearance between the two parts is too large.
② The manufacturing accuracy of pulley is low, and the end face or outer circle swing is large.
③ The poor installation quality of the active and passive pulleys makes the high-speed motion track of V-belt not on the same plane, resulting in working noise.
(3) Working parts of gear transmission
① The gear manufacturing accuracy is low and the pitch error is large.
② The center distance error of the transmission shaft of a pair of meshing gears is large. When the center distance is smaller than the standard, the interference sound between the teeth of the meshing transmission is generated; When the center distance is greater than the standard value, the impact sound will be produced.
③ The rolling bearing on the transmission shaft is worn seriously or the precision is low.
④ The center lines of the two transmission shafts on the gears are not parallel, so that the two gears can not mesh correctly.
⑤ The lubrication condition of a pair of meshing gears is poor. There is not enough lubricating oil
(4) Screw part of plastic sheet machine barrel
① The screw is assembled in the barrel, and the concentricity accuracy of the two parts is low.
② The perpendicularity error between the end face of the barrel and the flange end face of the barrel base and the center line of the barrel is large.
③ The screw is bent and deformed. The straightness error of the axis center line is too large.
④ The assembly clearance between the screw and its transmission shaft is too large. The center line of the two shafts is different from each other during the working rotation, so the error is large.

Scan the QR code to read on your phone

Previous: Reasonable use regulations and precautions of equipment
Next: What are the precautions for the safety of mechanical equipment?
Previous: Reasonable use regulations and precautions of equipment
Next: What are the precautions for the safety of mechanical equipment?

Related information

Reasonable use regulations and precautions of equipment
Reasonable use regulations and precautions of equipment
Reasonable use regulations and precautions of equipment
Time of issue : 2021-01-05 16:10:00
1. Use of equipment (1) Fixed person, fixed machine, voucher operation All operators of main production equipment must operate with certificate, and they are not allowed to use the equipment without certificate. ① Before the operators independently use the equipment, the factory shall conduct training and examination on the equipment structure, performance, technical specifications, maintenance knowledge, safe operation procedures and practical skills, and issue the operation certificate after passing the examination of the equipment and Tools Department, education department and labor and capital department. ② After training, operators of key equipment, imported equipment, refined, large, rare and key equipment shall pass the examination conducted by the equipment and Tools Department together with relevant departments, and then issue operation certificates. ③ For those who have the ability to operate multi-faceted equipment, they are allowed to operate 2-3 sets of equipment of the same type after passing the examination. For equipment operated by more than one person, the captain responsibility system must be implemented. ④ The personnel who operate and use the equipment temporarily can only use the equipment temporarily with the consent of the leader and the mechanic after training. ⑤ For those who are transferred out of the factory or are no longer using the original equipment due to the change of type of work, they must take back the operation certificate and submit it to the equipment and Tools Department for cancellation. (2) A number of disciplines for operators to make good use of and manage the equipment are stipulated In machinery industry system enterprises, the "Five Disciplines" for operators to use and manage equipment well are as follows: ① Use the equipment with the operation certificate and abide by the safety operation regulations; ② Keep the equipment clean and tidy and refuel according to regulations; ③ Follow the shift system; ④ Take good care of tools and accessories, and do not lose them; ⑤ If the fault is found, stop the machine immediately for inspection. If you can't handle it, inform the maintenance department. (3) Establish and improve the post responsibility system of operators According to the requirements of the post responsibility system, a special personnel mechanism shall be established for the equipment operated by individuals and operated by one shift; For the equipment operated by three shifts and several people, the captain responsibility system shall be established. In the unit, further division of operating posts and responsibilities, so that each equipment has a special person to manage, everyone has a special responsibility. (4) Establish and improve the package mechanism According to the different process characteristics and production conditions of the equipment, appropriate methods can be adopted. (5) Carry out competition activities of "red flag equipment" and "trustworthy equipment" The essence of equipment competition is people's competition, mainly aiming at the mental outlook and labor attitude of employees, operation and maintenance technology, and mutual cooperation. Through the competition, the "red flag equipment" was selected, and on this basis, the "trustworthy equipment" was further selected. Appropriate spiritual and material rewards should be given to operators and maintenance personnel of "red flag equipment" and "trustworthy equipment", so as to consolidate the sustainable development of competition activities. The standards of "red flag equipment" are generally as follows: ① Good completion of tasks, good attendance, good equipment performance, complete parts; ② The use of the equipment meets the specified requirements; ③ Do a good job in cleaning, lubricating, fastening, adjusting and anti-corrosion of equipment; ④ Equipment use records are complete and accurate. The standard of "trustworthy equipment" is higher than that of "red flag equipment". (6) Team equipment man This is in the grass-roots production team, the equipment staff elected by the staff group, to assist the team leader and workshop equipment staff to manage all the equipment in the team. In a larger team, several people can be elected to form an equipment management group. (7) Cultivate and establish advanced positions or teams In the production site equipment management, the cultivation and establishment of advanced posts and teams plays an immeasurable role in mobilizing the majority of employees to manage and use the equipment well.
See more information
1. Use of equipment (1) Fixed person, fixed machine, voucher operation All operators of main production equipment must operate with certificate, and they are not allowed to use the equipment without certificate. ① Before the operators independently use the equipment, the factory shall conduct training and examination on the equipment structure, performance, technical specifications, maintenance knowledge, safe operation procedures and practical skills, and issue the operation certificate after passing the examination of the equipment and Tools Department, education department and labor and capital department. ② After training, operators of key equipment, imported equipment, refined, large, rare and key equipment shall pass the examination conducted by the equipment and Tools Department together with relevant departments, and then issue operation certificates. ③ For those who have the ability to operate multi-faceted equipment, they are allowed to operate 2-3 sets of equipment of the same type after passing the examination. For equipment operated by more than one person, the captain responsibility system must be implemented. ④ The personnel who operate and use the equipment temporarily can only use the equipment temporarily with the consent of the leader and the mechanic after training. ⑤ For those who are transferred out of the factory or are no longer using the original equipment due to the change of type of work, they must take back the operation certificate and submit it to the equipment and Tools Department for cancellation. (2) A number of disciplines for operators to make good use of and manage the equipment are stipulated In machinery industry system enterprises, the "Five Disciplines" for operators to use and manage equipment well are as follows: ① Use the equipment with the operation certificate and abide by the safety operation regulations; ② Keep the equipment clean and tidy and refuel according to regulations; ③ Follow the shift system; ④ Take good care of tools and accessories, and do not lose them; ⑤ If the fault is found, stop the machine immediately for inspection. If you can't handle it, inform the maintenance department. (3) Establish and improve the post responsibility system of operators According to the requirements of the post responsibility system, a special personnel mechanism shall be established for the equipment operated by individuals and operated by one shift; For the equipment operated by three shifts and several people, the captain responsibility system shall be established. In the unit, further division of operating posts and responsibilities, so that each equipment has a special person to manage, everyone has a special responsibility. (4) Establish and improve the package mechanism According to the different process characteristics and production conditions of the equipment, appropriate methods can be adopted. (5) Carry out competition activities of "red flag equipment" and "trustworthy equipment" The essence of equipment competition is people's competition, mainly aiming at the mental outlook and labor attitude of employees, operation and maintenance technology, and mutual cooperation. Through the competition, the "red flag equipment" was selected, and on this basis, the "trustworthy equipment" was further selected. Appropriate spiritual and material rewards should be given to operators and maintenance personnel of "red flag equipment" and "trustworthy equipment", so as to consolidate the sustainable development of competition activities. The standards of "red flag equipment" are generally as follows: ① Good completion of tasks, good attendance, good equipment performance, complete parts; ② The use of the equipment meets the specified requirements; ③ Do a good job in cleaning, lubricating, fastening, adjusting and anti-corrosion of equipment; ④ Equipment use records are complete and accurate. The standard of "trustworthy equipment" is higher than that of "red flag equipment". (6) Team equipment man This is in the grass-roots production team, the equipment staff elected by the staff group, to assist the team leader and workshop equipment staff to manage all the equipment in the team. In a larger team, several people can be elected to form an equipment management group. (7) Cultivate and establish advanced positions or teams In the production site equipment management, the cultivation and establishment of advanced posts and teams plays an immeasurable role in mobilizing the majority of employees to manage and use the equipment well.
What are the reasons for the loud noise in the work of plastic sheet machine?
What are the reasons for the loud noise in the work of plastic sheet machine?
What are the reasons for the loud noise in the work of plastic sheet machine?
Time of issue : 2021-01-05 16:05:00
Motor position ① The rolling bearing for rotor shaft is seriously worn or the bearing accuracy is low. ② The rotor shaft is bent and deformed. ③ The installation position of carbon brush is incorrect. ④ Safety cover of rotor shaft end blade wiper motor. (2) V-belt drive part ① The V-belt pulley of plastic sheet machine is not fixed firmly on the transmission shaft or the fit clearance between the two parts is too large. ② The manufacturing accuracy of pulley is low, and the end face or outer circle swing is large. ③ The poor installation quality of the active and passive pulleys makes the high-speed motion track of V-belt not on the same plane, resulting in working noise. (3) Working parts of gear transmission ① The gear manufacturing accuracy is low and the pitch error is large. ② The center distance error of the transmission shaft of a pair of meshing gears is large. When the center distance is smaller than the standard, the interference sound between the teeth of the meshing transmission is generated; When the center distance is greater than the standard value, the impact sound will be produced. ③ The rolling bearing on the transmission shaft is worn seriously or the precision is low. ④ The center lines of the two transmission shafts on the gears are not parallel, so that the two gears can not mesh correctly. ⑤ The lubrication condition of a pair of meshing gears is poor. There is not enough lubricating oil (4) Screw part of plastic sheet machine barrel ① The screw is assembled in the barrel, and the concentricity accuracy of the two parts is low. ② The perpendicularity error between the end face of the barrel and the flange end face of the barrel base and the center line of the barrel is large. ③ The screw is bent and deformed. The straightness error of the axis center line is too large. ④ The assembly clearance between the screw and its transmission shaft is too large. The center line of the two shafts is different from each other during the working rotation, so the error is large.
See more information
Motor position ① The rolling bearing for rotor shaft is seriously worn or the bearing accuracy is low. ② The rotor shaft is bent and deformed. ③ The installation position of carbon brush is incorrect. ④ Safety cover of rotor shaft end blade wiper motor. (2) V-belt drive part ① The V-belt pulley of plastic sheet machine is not fixed firmly on the transmission shaft or the fit clearance between the two parts is too large. ② The manufacturing accuracy of pulley is low, and the end face or outer circle swing is large. ③ The poor installation quality of the active and passive pulleys makes the high-speed motion track of V-belt not on the same plane, resulting in working noise. (3) Working parts of gear transmission ① The gear manufacturing accuracy is low and the pitch error is large. ② The center distance error of the transmission shaft of a pair of meshing gears is large. When the center distance is smaller than the standard, the interference sound between the teeth of the meshing transmission is generated; When the center distance is greater than the standard value, the impact sound will be produced. ③ The rolling bearing on the transmission shaft is worn seriously or the precision is low. ④ The center lines of the two transmission shafts on the gears are not parallel, so that the two gears can not mesh correctly. ⑤ The lubrication condition of a pair of meshing gears is poor. There is not enough lubricating oil (4) Screw part of plastic sheet machine barrel ① The screw is assembled in the barrel, and the concentricity accuracy of the two parts is low. ② The perpendicularity error between the end face of the barrel and the flange end face of the barrel base and the center line of the barrel is large. ③ The screw is bent and deformed. The straightness error of the axis center line is too large. ④ The assembly clearance between the screw and its transmission shaft is too large. The center line of the two shafts is different from each other during the working rotation, so the error is large.
What are the precautions for the safety of mechanical equipment?
What are the precautions for the safety of mechanical equipment?
What are the precautions for the safety of mechanical equipment?
Time of issue : 2021-01-05 16:07:00
As one of the necessary conditions for daily production and construction of enterprises, mechanical equipment is the foundation of the survival and development of enterprises. It has an important impact on the production efficiency and production quality of enterprises, and is one of the important means to improve the profits of enterprises. The safety management of mechanical equipment has always been the key and difficult point of enterprise safety management. Precautions for mechanical safety Safety precautions for mechanical equipment 1、 Prevent general mechanical injury As a construction and production tool, the main body of production and operation of mechanical equipment is enterprise employees; Therefore, the enterprise should take necessary measures to implement relevant system arrangements to ensure the safety of the production and operation of the employees themselves. 1. Before the employees take up the post, they must undergo necessary skills training and safety training, and can only take the post after mastering the operation essentials of equipment and relevant safety precautions. 2. The enterprise shall strictly implement the relevant safety responsibility rules and regulations and the requirements of the operation standards for employees. 3. Employees must wear personal protective equipment correctly, and do not wear uneven, less or even not, without saving money; In the construction and production, the correct and comprehensive wearing of personal protective equipment can help prevent general injury in the mechanical equipment operation project, such as dust, abrasion and bleeding; Long hair must wear working hat, must wear three tight (neckline tight, sleeve tight, hem tight) work clothes, can not wear necklace and other hanging objects, operating rotary machine tool can not wear gloves. 4. The safety protection device of mechanical equipment must be used correctly according to the regulations, and it is not allowed to be used or removed. If any wear, aging or other conditions that fail to meet the safety protection are found, the relevant responsible person shall be informed in time for maintenance and replacement;
See more information
As one of the necessary conditions for daily production and construction of enterprises, mechanical equipment is the foundation of the survival and development of enterprises. It has an important impact on the production efficiency and production quality of enterprises, and is one of the important means to improve the profits of enterprises. The safety management of mechanical equipment has always been the key and difficult point of enterprise safety management. Precautions for mechanical safety Safety precautions for mechanical equipment 1、 Prevent general mechanical injury As a construction and production tool, the main body of production and operation of mechanical equipment is enterprise employees; Therefore, the enterprise should take necessary measures to implement relevant system arrangements to ensure the safety of the production and operation of the employees themselves. 1. Before the employees take up the post, they must undergo necessary skills training and safety training, and can only take the post after mastering the operation essentials of equipment and relevant safety precautions. 2. The enterprise shall strictly implement the relevant safety responsibility rules and regulations and the requirements of the operation standards for employees. 3. Employees must wear personal protective equipment correctly, and do not wear uneven, less or even not, without saving money; In the construction and production, the correct and comprehensive wearing of personal protective equipment can help prevent general injury in the mechanical equipment operation project, such as dust, abrasion and bleeding; Long hair must wear working hat, must wear three tight (neckline tight, sleeve tight, hem tight) work clothes, can not wear necklace and other hanging objects, operating rotary machine tool can not wear gloves. 4. The safety protection device of mechanical equipment must be used correctly according to the regulations, and it is not allowed to be used or removed. If any wear, aging or other conditions that fail to meet the safety protection are found, the relevant responsible person shall be informed in time for maintenance and replacement;
Home
About us
Company profile Culture
Products
Mechanical series
News
Company news Industry news
Jobs
Idea Recruitment

Contact us

 

Tel: 0754-87122065

Mobile: 15992216661

E-mail: 961912451@qq.com

Add：Workshop, Block A, Industrial Plant, Hongshi Area, Tuoji South Road, Jinping District, Shantou City

 

weicheng

QR code

Copyright (c)   Guangdong Shantou Weicheng Machinery Co., Ltd.  All Rights Reserved      粤ICP备2021063626号     Powered by www.300.cn